SiemensMania.cz

swimm3r · Zaslal: čt prosinec 08, 2005 11:49 pm Předmět: M55 dead

hello world!

I put "Tuningový FW10 pre Siemens M55" in my Siemens, and I don't Power On any more? Update went OK o the end but I can't do anything Shocked

I can't power up, or Update Firmware... What can I do????

HELPPPPPPPPPPPPPP!

hanni · Zaslal: pá prosinec 09, 2005 10:54 am Předmět:

You must unlock your phone.
Program Freia - Unlocking function - Direct unlock no map is saved - write your IMEI and push OK + red button on your phone...

http://www.siemensmania.cz/download.php?file=/software/Freia15Setup.exe

swimm3r · Zaslal: pá prosinec 09, 2005 8:49 pm Předmět:

hello again

FREIA - Engine build 15, Frontend build 11
Thanks goes out for the following:
Maxim, Rolis, Sergey, PapaJoe, Lead,
TheWizard, Jozso (for hardware and cable
support and of course beta testing),
Nico, Pinker, Tom, Crew
and all the others who supports ...
COMM_LoadBoots : selected phone family is 10
TTY_OpenCOMPort : opening Prodigy
COMM_IsBootRunning : bootcode does not seem to be running
COMM_LoadBoots : Waiting to power on the phone ...
COMM_LoadBoots : phone is not powered on

I can't power it up Sad

all others programs give to me "No Ping" (all the settings are good Sad

)

What the **** do I do now : Embarassed

swimm3r · Zaslal: pá prosinec 09, 2005 9:42 pm Předmět:

I can't do anything with it Brick wall

what happend? Rolling Eyes

all firmware program show only errors Brick wall

I push Power On button, but no effect Think

swimm3r · Zaslal: so prosinec 10, 2005 8:16 am Předmět:

when I install "M55_040101.exe"

with Pre-Check Skip all system freeze, and if I unplug Serial Cable, it unfreeze and I get this message "Error on waiting for Ack EOT";

with Pre-Check I get this message "Could not Ping Mobile";

I have Original Serial x55 Cable

All these things happend after I flash "FUBU_M55v10_3.6MB_tuning.bin" with JokerV0306.exe !!!

I can't power on and all software give "Could not Ping Mobile" ERROR Exclamation

Little_S · Zaslal: so prosinec 10, 2005 12:32 pm Předmět:

do you have your own EEPROM backup?
rewrite it using v-klay (or something alike) then you'd be able to turn your phone on.

swimm3r · Zaslal: so prosinec 10, 2005 2:31 pm Předmět:

I pushed the red button, I'm not so dumb... the ****ing phone doesn't start

swimm3r · Zaslal: so prosinec 10, 2005 2:35 pm Předmět:

I made FullFlash from my phone, but I can't use it !!!

when I push the button nothing happend... can it be phisicaly broken?! Think

lacibogi · Zaslal: so prosinec 10, 2005 2:42 pm Předmět:

You need to cut testpoint if you have tried all known solutions.

http://www.siemensmania.cz/download.php?file=/testpointy/M55_testpoint.zip

swimm3r · Zaslal: so prosinec 10, 2005 3:42 pm Předmět:

Torx 5 is for Siemens M55 ?

lacibogi · Zaslal: so prosinec 10, 2005 3:46 pm Předmět:

Yes, I think so. It´s universal.

swimm3r · Zaslal: so prosinec 10, 2005 4:22 pm Předmět:

thanks to all of you for your help. Now I will find the right tool to open my Siemens and cut that "thing".

I will write new things when I'm done with that !

thanks again! Smile