Master Patch - Instructions in English?

[kilibo]

Would somebody be so kind and help me translate this.
I mostly understand it, since i'm croatian, but I need some clarification
-------------------------------------------------------------------
Inštrukcie:
-stiahnite si a aplikujte Function Library pre svoj telefón
-vytvorťe zložku 0:/Misc/Patches/ptc-vkopírujte tam texťák configs.txt
-aplikujte Master patch
-nahrajte Master Midlet
-aplikujte patche závislé na Master Patchi
-v Master Midlete si môžete teraz jednotlivé patche konfigurovať
-po nastavení je potrebný refresh-v tomto prípade je to synchronizácia


Function Library:
-obsahuje adresy, ktoré sa v patchoch najčastjšie využívajú
-sú odlišné pre každý model telefónu a firmware-u avšak hlavná časť je všade rovnaká. (Preto ich z časti dokáže portovať Smelter)
-vďaka, tejto knižnici sú všetky novo vyrábané patche kompatibilné so všetkými telefónmi, portovať je preto pri týchto patchoch potrebné len jeden "riadok"

Master Patch:
-skenuje nastavenie patchov, výsledky zapisuje do configs.txt
-počas synchonizácie nahráva zmeny do RAM
-vďaka tomu sa už nemusíme trápiť nastavovaním súborov *.vkp
-nastaviť je potrebné len model telfónu-riadky Vám vyhovujúce zakomentujte


Ako môže dopadnúť práca s Master Patchom si môžete pozrieť tu.

Link

[beardie]

Instructions:
-download and apply function libraries for your telephone
-create folder 0:/Misc/Patches/ptc
-apply Master Patch
-save Master midlet to the phone
-apply patches which need Master patch
-in Master midlet (java application) you can configure now these patches
-after setting up - you need to refresh your phone, use synchonization ( or just switch it off and on)

Function Library:
-contains addresses, which are mostly used in patches
-they are different for each phone nad firmware version, but the main part is similar (smelter can port some of their parts)
-thanks to this library, all new created patches are compatible with all phone types, you need to port only the entrypoint

Master Patch:
-scans the patch config and result saves to configs.txt
-during the synchronization it saves changes to RAM
-thats for you dont need to change *.vkp files
-you have to change only the telepone type

how it works you can find here LINK

[kilibo]

Thanks for translation. This is what I did so far, but it's not working.
When i run Master Middlet from phone, I get error message
"Can not open configs.txt". It seems that there are no config.patches installed"

This is how I went to apply this patch, maybe I made a mistake somewhere?

1. With v_klay I applied function library(library.vkp)
2. Then I created folder in "Siemens Device\Data\Misc\Patches\ptc"
3. With v_klay, applied Master Patch(master5.vkp)
4. Uploaded and installed Master Middlet(Master.jar & Master.jad)
5. Then i applied patch with v_klay "extra_info6.vkp"

When I apply patch, do I need to modify that patch before applying it to the phone?
For example, I see memory addresses are listed for different phones. Do I need to modify specific memory address in this specific patch?

;16B60B4: 0xA0B9026B 0xA0FC1B01 ; S65v58
;172F4A0: 0xA0BA39AB 0xA0FC1B01 ; CX70v50

[lacibogi]

If there are more addresses in the patch you must uncomment (remove the line for S65 (or for your phone). The rest must be commented.
And Master Patch is not MSPatchLoader. It is Master patch.

[kilibo]

Thanks for your help. I made a mistake with #3 step.

1. With v_klay I applied function library(library.vkp)

2. Then I created folder in "Siemens Device\Data\Misc\Patches\ptc"

3. With v_klay, applied Master Patch Loader(S65v58_MSPatchloader.vkp) <- wrong
3.I should have loaded Mater Patch(master5.vkp)

4. Uploaded and installed Master Middlet(Master.jar & Master.jad)

5. Then i applied patch with v_klay "extra_info6.vkp"
by removing ";" for line with memory address for S65

[hyoga]

i have a problem when apli the patch i try of switch on mi phone but nothing happens, what if i don't aplied the library patch it can be that ?

[alkaba]

Yes, you must apply the function library patch that´s it

[hyoga]

ok but what is that patch?? can you give me the link?? please thank

[kilibo]

[acetm]

I've applied Master pach v5, Functuions library and Graphloader 3.1 AV with Blinker 2.2. It works fine. Then I want to apply Start menu, but the phone swithed off when boot. The pictures also applied so I don't know what was the problem. There are 2 kind of master patch with different Graploader. Is it possible that it needs the second kinf of masterpatch? My phone is S65 fw58.

[lacibogi]

I have the second version of master patch and everything works fine.